|
Post by btreichel on Sept 17, 2019 23:20:32 GMT
JCB, was wondering the same thing. But just want the collet and bits. All of my current ones are 1/8"
|
|
hans
Full Member
Posts: 151
Machine: Other
|
Post by hans on Sept 17, 2019 23:35:50 GMT
And I wanted the T-plate table, but ? ? ? I'm hoping that this is more a "committed expression of interest" than an ordering process. Derek?
|
|
|
Post by btreichel on Sept 17, 2019 23:45:48 GMT
And I wanted the T-plate table, but ? ? ? I'm hoping that this is more a "committed expression of interest" than an ordering process. Derek? "user avatar MillRight CNCCreator 19 minutes ago Hey Ben. Thank you for backing. The options table is displayed further down on the page. You can add to your pledge amount for the sum of the options you want. For instance, if you wanted to add the collet you would add $27 to your pledge amount. There will be a backer survey later to make sure we are all on the same page with what options you have selected and make sure we aren't over or short on your pledge amount." From the comments on kickstarter. Figure I would post this since I figure they are pretty busy.
|
|
|
Post by aquanub on Sept 18, 2019 0:18:35 GMT
congrats derek! met the kickstarter goal within the hour!
|
|
|
Post by Derek the Admin on Sept 18, 2019 5:36:34 GMT
Thanks to everyone who backed and everyone else that has wished us well. We have made our first post in the update section that we think will clarify some of these questions about options. See link below: /posts/2626736Thanks again ladies and gents.
|
|
|
Post by Derek the Admin on Oct 9, 2019 20:23:11 GMT
|
|
viddall
New Member
Posts: 33
Location: Maryland
Machine: Power Route
|
Post by viddall on Oct 17, 2019 12:17:10 GMT
Hey Derek, You may have answer this on another post, sorry if you have. 1) do you have an estimate on when you would be releasing the 4th axis for the power route? 2) would you be able to manufacture quad start screws? Thanks
|
|
|
Post by Derek the Admin on Oct 17, 2019 22:46:34 GMT
Hey.
1) It will probably be sometime early Jan 2020. It depends on how some other things go though. 2) We could, but we wouldn't be as good as it as others would.
|
|
viddall
New Member
Posts: 33
Location: Maryland
Machine: Power Route
|
Post by viddall on Oct 18, 2019 14:12:05 GMT
Hey. 1) It will probably be sometime early Jan 2020. It depends on how some other things go though. 2) We could, but we wouldn't be as good as it as others would. sorry, for #2 I should've asked if withthe 4th axis I could do multiple start lead screws? Thanks, for the reply
|
|
|
Post by Derek the Admin on Oct 18, 2019 16:55:09 GMT
Probably not. Something like that would take more precision than you could achieve.
|
|
|
Post by emcolejr on Oct 24, 2019 2:31:42 GMT
I purchased a Mark V on Kickstarter. Is it possible to view the assembly manual in advance of shipment?
|
|
|
Post by Derek the Admin on Oct 25, 2019 23:37:36 GMT
We will release it when we're done with it. It probably won't be until a little bit prior to shipment.
|
|
|
Post by jamesma70 on Oct 30, 2019 15:10:58 GMT
What are the specs on the T slot bed? I am looking at options for clamping and would like to know what options are available.
|
|
|
Post by billiam on Nov 1, 2019 16:29:06 GMT
I saw that the PowerRoute's spindle extends about 3/4" beyond the edge of the spoilboard. Is that distance about the same for the Mega V?
If I wanted to mill the end of a board, upright, would I be better off cutting a ways into the spoil board, or adding a spacer to the router mount?
|
|
|
Post by Derek the Admin on Nov 2, 2019 2:03:30 GMT
I saw that the PowerRoute's spindle extends about 3/4" beyond the edge of the spoilboard. Is that distance about the same for the Mega V? If I wanted to mill the end of a board, upright, would I be better off cutting a ways into the spoil board, or adding a spacer to the router mount? Close to the same, but on the Mega V can mount the bed a little further back to give yourself a little more overhsng.
|
|