Post by justsomeguy on Aug 26, 2021 21:02:03 GMT
Some help on this would be greatly appreciated...
I have been using my M3 for 2 years now without an issue. The only difference between then and now is that I am using the UGS download from the MillRight resources page instead of the original net Bean 8.1 download from 2 years ago. Now the router on my M3 plunges straight down thru everything... material, spoil board and main board when I hit the start button/arrow. I set up everything as I have done in the past when all was working correctly but now instead of starting the cutting when pressing the start arrow... it plunges straight down instantly. As I mentioned, the only difference is i switched to the MillRight UGS download, where I had been using NetBean 8.1 UGS. I tend to be able to work out mechanical problems but not so good with computers/software, etc.
Can anyone tell me what is happening and/or what I need to do to correct this? I attached the beginning of the G code as it was downloaded from Fusion360... Is there something in the G code that is making the router plunge? Has something gone bad in the electronics? I am getting pretty frustrated and am becoming desperate for answers. Please help...
Thank you
(viperlitewingstif2)
(viperlitewingstif2)
(T1 D=1.587 CR=0 - ZMIN=-4.175 - flat end mill)
G90 G94
G17
G21
(When using Fusion 360 for Personal Use, the feedrate of)
(rapid moves is reduced to match the feedrate of cutting)
(moves, which can increase machining time. Unrestricted rapid)
(moves are available with a Fusion 360 Subscription.)
G28 G91 Z0
G90
(2D Contour1)
T1
S5000 M3
G54
M8
G0 X-0.071 Y-0.015
Z15
G1 Z5 F1000
Z3.3 F333.3
Z-1.929
X-0.063 Z-1.978 F1000
X-0.041 Y-0.016 Z-2.022
X-0.006 Z-2.057
X0.039 Y-0.017 Z-2.08
X0.088 Z-2.088
X0.246 Y-0.02
X0.295 Y-0.012
X0.34 Y0.01
X0.376 Y0.044
X0.399 Y0.088
X0.407 Y0.137
X0.409 Y0.256
X0.397 Y1.147
X0.361 Y2.025
X0.301 Y2.891
Reply
I have been using my M3 for 2 years now without an issue. The only difference between then and now is that I am using the UGS download from the MillRight resources page instead of the original net Bean 8.1 download from 2 years ago. Now the router on my M3 plunges straight down thru everything... material, spoil board and main board when I hit the start button/arrow. I set up everything as I have done in the past when all was working correctly but now instead of starting the cutting when pressing the start arrow... it plunges straight down instantly. As I mentioned, the only difference is i switched to the MillRight UGS download, where I had been using NetBean 8.1 UGS. I tend to be able to work out mechanical problems but not so good with computers/software, etc.
Can anyone tell me what is happening and/or what I need to do to correct this? I attached the beginning of the G code as it was downloaded from Fusion360... Is there something in the G code that is making the router plunge? Has something gone bad in the electronics? I am getting pretty frustrated and am becoming desperate for answers. Please help...
Thank you
(viperlitewingstif2)
(viperlitewingstif2)
(T1 D=1.587 CR=0 - ZMIN=-4.175 - flat end mill)
G90 G94
G17
G21
(When using Fusion 360 for Personal Use, the feedrate of)
(rapid moves is reduced to match the feedrate of cutting)
(moves, which can increase machining time. Unrestricted rapid)
(moves are available with a Fusion 360 Subscription.)
G28 G91 Z0
G90
(2D Contour1)
T1
S5000 M3
G54
M8
G0 X-0.071 Y-0.015
Z15
G1 Z5 F1000
Z3.3 F333.3
Z-1.929
X-0.063 Z-1.978 F1000
X-0.041 Y-0.016 Z-2.022
X-0.006 Z-2.057
X0.039 Y-0.017 Z-2.08
X0.088 Z-2.088
X0.246 Y-0.02
X0.295 Y-0.012
X0.34 Y0.01
X0.376 Y0.044
X0.399 Y0.088
X0.407 Y0.137
X0.409 Y0.256
X0.397 Y1.147
X0.361 Y2.025
X0.301 Y2.891
Reply
