Post by easyar15dotcom on Jun 27, 2019 19:19:37 GMT
Looking for some help with a UGS error.
Quick background:
-Initially installed UGS with a new M3 purchase.
-Worked fine for a short time then started to receive a looping "Error While Processing Response" when connecting the COM/baud.
-Only way to clear the issue is with a full restart of the computer.
-Couldn't find a clear solution with internet searches and switched to the paid version of PicSender.
I would like to go back to UGS and am wondering if anyone else has seen this issue before? Wondering if its a $$ issue because the same error occurs no matter what UGS build I am running (UGS vs Platform vs Stable vs Classic).
*If this seems like a GRBL/UNO issue to any of you, is there a way to update my UNO board to a more compatible version? I have seen comments about "flashing" but I'm totally lost on what that is or how to do it.
Attached below are my $$ settings:
$0=10 (step pulse, usec)
$1=255 (step idle delay, msec)
$2=0 (step port invert mask:00000000)
$3=0 (dir port invert mask:00000000)
$4=0 (step enable invert, bool)
$5=0 (limit pins invert, bool)
$6=0 (probe pin invert, bool)
$10=2 (status report mask:00000010)
$11=0.010 (junction deviation, mm)
$12=0.002 (arc tolerance, mm)
$13=1 (report inches, bool)
$20=0 (soft limits, bool)
$21=0 (hard limits, bool)
$22=0 (homing cycle, bool)
$23=0 (homing dir invert mask:00000000)
$24=25.000 (homing feed, mm/min)
$25=600.000 (homing seek, mm/min)
$26=244 (homing debounce, msec)
$27=4.000 (homing pull-off, mm)
$100=40.000 (x, step/mm)
$101=40.000 (y, step/mm)
$102=40.000 (z, step/mm)
$110=8000.000 (x max rate, mm/min)
$111=8000.000 (y max rate, mm/min)
$112=6000.000 (z max rate, mm/min)
$120=250.000 (x accel, mm/sec^2)
$121=250.000 (y accel, mm/sec^2)
$122=500.000 (z accel, mm/sec^2)
$130=264.000 (x max travel, mm)
$131=264.000 (y max travel, mm)
$132=69.000 (z max travel, mm)
ok
Quick background:
-Initially installed UGS with a new M3 purchase.
-Worked fine for a short time then started to receive a looping "Error While Processing Response" when connecting the COM/baud.
-Only way to clear the issue is with a full restart of the computer.
-Couldn't find a clear solution with internet searches and switched to the paid version of PicSender.
I would like to go back to UGS and am wondering if anyone else has seen this issue before? Wondering if its a $$ issue because the same error occurs no matter what UGS build I am running (UGS vs Platform vs Stable vs Classic).
*If this seems like a GRBL/UNO issue to any of you, is there a way to update my UNO board to a more compatible version? I have seen comments about "flashing" but I'm totally lost on what that is or how to do it.
Attached below are my $$ settings:
$0=10 (step pulse, usec)
$1=255 (step idle delay, msec)
$2=0 (step port invert mask:00000000)
$3=0 (dir port invert mask:00000000)
$4=0 (step enable invert, bool)
$5=0 (limit pins invert, bool)
$6=0 (probe pin invert, bool)
$10=2 (status report mask:00000010)
$11=0.010 (junction deviation, mm)
$12=0.002 (arc tolerance, mm)
$13=1 (report inches, bool)
$20=0 (soft limits, bool)
$21=0 (hard limits, bool)
$22=0 (homing cycle, bool)
$23=0 (homing dir invert mask:00000000)
$24=25.000 (homing feed, mm/min)
$25=600.000 (homing seek, mm/min)
$26=244 (homing debounce, msec)
$27=4.000 (homing pull-off, mm)
$100=40.000 (x, step/mm)
$101=40.000 (y, step/mm)
$102=40.000 (z, step/mm)
$110=8000.000 (x max rate, mm/min)
$111=8000.000 (y max rate, mm/min)
$112=6000.000 (z max rate, mm/min)
$120=250.000 (x accel, mm/sec^2)
$121=250.000 (y accel, mm/sec^2)
$122=500.000 (z accel, mm/sec^2)
$130=264.000 (x max travel, mm)
$131=264.000 (y max travel, mm)
$132=69.000 (z max travel, mm)
ok